Tweet
Topic originally created by Ian Levy on July 17, 2012 6:54 PM and viewed 4232 times in the old forum.
-
-
Originally posted by Ian Levy on July 17, 2012 6:54 PM
Hello
Does anyone have a source for the hard rubber bungs that fit the driving light adjustment holes under the front bumper next to the brake cooling ducts?
John-yes it is still raining heavily here & this is summer!!
Regards & thanks
Ian L
-
Originally posted by JBishop on July 22, 2012 5:31 PM
Ian
You can get rubber ones that fit correctly, but they are not correct. I have found similar plastic ones but they were the wrong size by just a millimeter or 2. So no good.
And I knew it would still be raining. Hang in there. There is always next year's summer if that arrives.
John
Comment
-
Originally posted by sam231 on July 23, 2012 10:53 PM
Ian,
I may give these guys a shot. They have a hole plug that on the out side looks like ours. I think the hole is 2" in diameter so should fit. Never heardd a concours judge say "Pull out that plug and let me look at it." Hope this works http://store.polarwire.com/browse.cf...bushings-plugs
Cheers,
Sam
Comment
-
Originally posted by Aaron on July 24, 2012 8:47 AM
Ian,
I have a whole box of 2 inch plugs that look just like what is in the picture in "gromets and plugs".
It is a nice fairly substantial hard plastic plug but it is 2 inches, which is slightly larger then the 50mm hole. I gournd down a couple of them and stuffed
them in the holes in my car, it looks good from the outside and I agree with you, I doubt a judge will as that they be removed. However, it isn't right and it
is a bit micky mouse. If you would like a couple to play with, send be an address and I can put them in an envelope.
I had thought about enlarging the hole - but decided against it thinking that someday I may come across the correct 50 mm plugs
Aaron
Comment
-
Originally posted by Aaron on July 24, 2012 9:31 AM
What about these?
It looks like I will have some spares on Thursday
A
Comment
-
Originally posted by Trachsel on July 27, 2012 6:29 PM
what about here ?www.korrosionsschutz-depot.de/shop_xtc/product_info.php
Regards, Jacques
Comment
-
Originally posted by Gandinell on July 28, 2012 3:36 AM
50mm
Ciao, Roberto
Comment
-
Originally posted by Ian Levy on August 1, 2012 9:13 PM
Hi Aaron
I have just picked up these plugs from local dealer.
Would fit but have a large cross carved in th middle so still looking.
Thanks
Ian L
Roberto
Viele danke aber ich habe kein Deutsch
Comment
-
Originally posted by dbone on June 16, 2014 1:17 PM
Ian
have you found replacements for these plug? The Swiss source looks good, I just can not get through that web site.
i had very old ones before my paint job, now I don't. I need to make a call to the painter.
Comment
-
Originally posted by dkblueUK on June 16, 2014 5:47 PM
Dave, I have a spare pair of flat 50mm grommets that fill the holes, and look right. Whether they are "correct" , I don't know. If you would like them, pm me your address, and I will send them. Regards, NeilComment
-
Originally posted by Ian Levy on June 16, 2014 6:10 PM
Dave
I have not found any that fit & look right
I ordered two from Korrosionschutz in Germant & they were slightly tpp small.
50 mm grommets are too small on my car & are not a fit.
I will get on the Distrelelc site & let you know
Regards
Ian
Comment
-
Originally posted by dbone on June 17, 2014 1:11 PM
Ian,
i just rechecked the hole size, mine are 50mm.
Neil, just sent you a pm with address
dave
Comment
Comment